PENGOLAHAN ZEOLIT SEBAGAI BAHAN PENGUAT

Sajaratud Dur

Abstract


Penelitian pengolahan zeolit sebagai bahan penguat dilakukan untuk memanfaatkan sumber daya alam yang ada di Provinsi Sumatera Utara. Pengolahan zeolit tersebut sehingga berukuran nanometer dengan menggunakan ballmill. Pengaktifan zeolit dilakukan dengan pemanasan 1050 C selama 10 menit. Ukuran partikel zeolit yang dihasilkan adalah 290 nanometer. Hal ini diperoleh dari 80 gram zeolite berukuran 1700 nanometer menjadi 15 gram berukuran 290 nanometer selama 34 jam proses grinding di dalam ballmill.

 

Kata Kunci: zeolit, nanometer, pengolahan, penguat

 


Full Text:

PDF PDF

References


Adriana, Zaimahwati, Ramzi, Supardin, (2008), “Pembuatan Kayu Plastik dari Limbah Kayu Kelapa Sawit dan Polistirena Menggunakan Teknik Impregnasi Reaktif “, Prosiding Seminar nasional Sain dan Teknologi BRR NAD-Nias, Banda Aceh.

Aini, M.N., dan Indriati, L., (2007), “Proses Pemutihan Zeolit sebagai Bahan Pengisi Kertas”, Buletin, Balai Besar Pulp dan Kertas, Bandung.

Bukit, N, (2011), “Pengolahan Zeolit Alam sebagai Bahan Pengisi Nano Komposit

Polipropilena dan Karet alam SIR-20 dengan Kompatibelizer Anhidrida Maleat-Grafted Polipropilena”, Disertasi, Fakultas Matematika dan Ilmu Pengetahuan Alam, Universitas Sumatera Utara, Medan.

Callister, Jr. and William, D. (2007), “Material Science and Engineering and Introduction” United State of America.

Hanafi, I., Halimatuddahliana, dan Hazizan, (2005), “Properties of Polypropylene/Ethylene-Propylene Diene Terpolymer/Natural Rubber (Pp/Epdm/Nr) Ternary Blend: The Effect of Dynamic Vulcanization”, Solid State Science and Technology, Vol.13, No.1 & 2.

Harahap, S, (2006), “Kajian Bahan Laporan Akhir, Badan Penelitian dan Pengembangan Propinsi Sumatera Utara, Medan.

Hull, D, (1992), “An Introduction to Composite Material”, Cambridge University Press, London.

Ismail, H, Salmah, Nasir, M, (2000), “Dynamic Vulcanization of Rubber Wood-Filled Polypropylene/Natural Rubber Blends”, Polymer Testing, 819-823.

Ketan, K.M., (2002), “A Literature Survey On Nanocomposites” University of of Massachussetts Lowell: Master of Science Thesis.

Kohls, J. J., and Beaucage, (2002), “Rational Desing of Reinforced Rubber”, Cur OP. Solid St Mat Sci., 6:183-194.

Leblanc, J. R, (2002), “Rubber-Filler Interaction and Rheology Properties in Filled Compound, Prog.Polym.Sci 27: 627-687.

Makadia, C.M., (2000), “Nanocomposites of Polypropylene by polimer Melt Compounding Approach”, University of Massachussetts Lowell: Master of Science Thesis.

Mc.Bain, J.W, (1932), “The Sorption of Gases and Vapors by Solids”, Chapter 5, Rutledge and Sons, London.

Micheler, G. H., (2008), “Electron Microscopy of Polymers”, Germany: Springer Laboratory

Mozgawa, W, Krol, M, and Barczyk, K, (2011), “ FT-IR Studies of Zeolites from Different Structural Groups, Faculty of Materials Science and Ceramics, AGH University of Science and Technology, Kraków, Please cite as: CHEMIK, 65, 7, 667-674

Pandey, J.K, Chu, W.S, Kim, C.S, and Ahn, S.H, (2009), “Bio-nano Reinforcement of Environmentally Degradable Polimer Matrix by CelluloseWhisker Form Grass”, Composite: Part B 40, 676-680.

Pandey, C.S, and Ahn, S.H, (2010), “Preparation and Properties of Bionanoreinforced Composites from Biodegradable Polymer Matrix andCellulose Whiskers”, Journal of Applied Polymer Science. 115 (4): 2493-2501.

Sembiring, R.S., (2014), “Penyediaan Nanokomposit Karet Alam-g-Glysidil Metacrilate/Bentonit”, Tesis Magister. Program Pascasarjana USU. Medan

Stevens, M. P., (2001), “Kimia Polimer”, Cetakan Pertama, Pradnya Paramita Jakarta.

Subiyanto, B, Suryanegara, L, Yano, H, (2006), “Perana Bio-nano Komposit dalam Industri di masa Depan”, UPT BPP Biomaterial-LIPI, Laporan Teknik.

Umemura, K, (2006), “ Wood-Based Materials and Wood Adhesives”: Recent Trend in Japan. Cibinong: Makalah Wood Science School di UPT Biomaterial LIPI.


Refbacks

  • There are currently no refbacks.